Scantech Vega V-1010 Manual de usuario Pagina 120
- Pagina / 138
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
118
Autostand
This mode allows you to switch from Flashing trigger mode to Level
trigger mode.
Autostand begins in flashing mode: At power up the lighting and
decoding are on (no need to activate the trigger line) and after a period
of inactivity lasting the time specified by the trigger timeout, the
scanner starts flashing.
To switch to Level trigger mode activate the trigger line (press the
trigger).
When in Level trigger mode, after a period of inactivity lasting the time
specified by the trigger timeout, the scanner switches back to flashing
mode.
Toggle
This mode allows lighting and decoding toggle when the trigger line is
activated.
First trigger activation = lighting and decoding on, second trigger
activation = lighting and decoding off.
Presentation
This mode allows power up lighting and decoding are on. After a period
of inactivity lasting the time specified by the trigger timeout, the lighting
turns off or is dimmed. When a new bar code is presented the lighting
and decoding restart and stay on until another period inactivity.
- Handheld Bar code Scanner 1
- Scantech-ID VEGA 3
- Table of contents 5
- Introduction 9
- Chapter 1 Product Safety 10
- 1.1 SAFETY & CAUTION 11
- 1.2 FCC WARNING 12
- 1.3 SCANNER LABELLING 13
- 12 General Description 14
- 2.1 USE OF THE VEGA 15
- 3.1 V-1020 UNPACKING 17
- 3.2 V-1020 MOUNTING 18
- 3.3 V-1020 USB DRIVER 19
- 4.1 V-1020BT UNPACKING 21
- 20 Configuring the VEGA 22
- Pairing 23
- 22 Configuring the VEGA 24
- Sleep Mode 25
- Memory Mode 25
- Chapter 5 Cover Display 26
- 5.1 SETUP COVER DISPLAY 27
- Message Format 27
- Change Cover Display 27
- 26 Configuring the VEGA 28
- 28 Configuring the VEGA 30
- 6.1 PREFACE 32
- 6.2 FACTORY DEFAULT SETTING 34
- Chapter 7 Programming Codes 35
- 7.1 RETURN TO DEFAULT 36
- 7.2 RS-232 MODE PARAMETERS 37
- Baud rate 37
- Data bits 39
- Stop bits 39
- RS-232 Parameters–ENQ 40
- RS-232 Parameters–ACK 41
- RS-232 Parameters–NAK 41
- Software Protocol–XON/XOFF 42
- Hardware Protocol–RTS/CTS 42
- RS-232 Parameters-LRC 43
- 7.3 BLUETOOTH SCANNER SETUP 45
- Bluetooth Default Setting 45
- Scanner Server/Client Mode 45
- Set Scanner Pin Code Mode 46
- Set Pin Code Charactor 47
- 7.4 BLUETOOTH CRADLE SETUP 48
- Set Cradle Pin Code Mode 48
- Set Pin Code Barcode 48
- Set Cradle Interface Barcode 49
- 7.5 DECODING SELECTION 56
- Symbologies Selection 56
- Disable All Symbologies 65
- 7.7 AZTEC SETTINGS 67
- Structure Append Mode 67
- Aztec Runes 67
- GS1-128 Emulation 67
- 7.8 BPO SETTINGS 69
- 7.9 CANADA POST SETTINGS 70
- 7.10 CODABAR SETTINGS 71
- Start/Stop 71
- CLSI Library System 72
- Concatenation 73
- 7.11 CODABLOCK SETTINGS 74
- 7.12 CODE 11 SETTINGS 75
- Check Digits 75
- 7.13 CODE 39 SETTINGS 76
- Accepted Characters 77
- Reading Range 78
- Reading Tolerance 78
- GS1-128 Identifier 80
- ISBT 128 82
- GTIN Processing For GS1-128 83
- Unconventional GS1-128 83
- 7.16 DATAMATRIX SETTINGS 84
- 7.17 DUTCH POST SETTINGS 85
- Reading Type 86
- Supplemental Setup 88
- 7.19 GS1 COMPOSITE SETTINGS 91
- 7.20 GS1 DATABAR SETTINGS 93
- 7.21 INFOMAIL SETTINGS 94
- 7.23 JAPAN POST SETTINGS 97
- 7.24 MATRIX 2 OF 5 SETTINGS 98
- 7.25 MAXICODE SETTINGS 99
- 7.26 MICROPDF417 SETTINGS 100
- Symbology Identifier 100
- Code 128 Emulation 100
- Check Digit Verification 101
- 7.28 PDF417 SETTINGS 102
- Irregular PDF 102
- Control Header 102
- Optional Fields 103
- 7.29 PLANET SETTINGS 105
- Check Digit Transmission 105
- 7.31 POSTNET SETTINGS 107
- 7.32 QR CODE SETTINGS 108
- Model 1 Control 108
- 7.34 SWEDEN POST SETTINGS 111
- 7.35 TELEPEN SETTINGS 112
- 7.36 TLC 39 SETTINGS 113
- Linear Transmission Only 113
- ECI security 113
- Preamble 115
- Postamble 116
- Scantech-ID 117
- 8.1 SCANNING TRIGGERING 118
- 8.2 TIME OUT 121
- 8.3 GOOD READ MODE 122
- 8.4 BUZZER BEEP TONE 123
- Beep Tone Setup 123
- Good Read Beeps 123
- Beep Duration 124
- 8.5 GOOD READ DURATION 125
- Good Read Led Duration 125
- Error Beep 125
- Setup Beep 126
- Chapter 9 Imager settings 127
- 9.1 IMAGER MODE 128
- Appendixes 129
- A.DECIMAL VALUE TABLE 130
- B.ASCII TABLE 131
- C.READABLE SYMBOLOGIES 132
- 1D Symbologies 132
- 2D Symbologies 132
- D.TECHNICAL SPECIFICATIONS 133
- E.SCAN MAP 135
- F.OVERVIEW MODEL NUMBERS 137
Relacionado con productos y manuales para Lectores De Códigos De Barras Scantech Vega V-1010
(1 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales