Scantech Vega V-1010 Manual de usuario descargar pdf (Pagina 12)

10 General Description

1.2 FCC WARNING

This equipment complies with the requirements in Part 15 of FCC.

Any operation must comply with the conditions below:

(a) The equipment will not cause any severe interference.

(b) The equipment can avoid any interference from environment.

Statement:

This product is classified as A class product.

In environment this product may cause some interference.

In this situation the user may do something to avoid

interference.

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 137 138

Handheld Bar code Scanner 1
Scantech-ID VEGA 3
Table of contents 5
Introduction 9
Chapter 1 Product Safety 10
1.1 SAFETY & CAUTION 11
1.2 FCC WARNING 12
1.3 SCANNER LABELLING 13
12 General Description 14
2.1 USE OF THE VEGA 15
3.1 V-1020 UNPACKING 17
3.2 V-1020 MOUNTING 18
3.3 V-1020 USB DRIVER 19
4.1 V-1020BT UNPACKING 21
20 Configuring the VEGA 22
Pairing 23
22 Configuring the VEGA 24
Sleep Mode 25
Memory Mode 25
Chapter 5 Cover Display 26
5.1 SETUP COVER DISPLAY 27
Message Format 27
Change Cover Display 27
26 Configuring the VEGA 28
28 Configuring the VEGA 30
6.1 PREFACE 32
6.2 FACTORY DEFAULT SETTING 34
Chapter 7 Programming Codes 35
7.1 RETURN TO DEFAULT 36
7.2 RS-232 MODE PARAMETERS 37
Baud rate 37
Data bits 39
Stop bits 39
RS-232 Parameters–ENQ 40
RS-232 Parameters–ACK 41
RS-232 Parameters–NAK 41
Software Protocol–XON/XOFF 42
Hardware Protocol–RTS/CTS 42
RS-232 Parameters-LRC 43
7.3 BLUETOOTH SCANNER SETUP 45
Bluetooth Default Setting 45
Scanner Server/Client Mode 45
Set Scanner Pin Code Mode 46
Set Pin Code Charactor 47
7.4 BLUETOOTH CRADLE SETUP 48
Set Cradle Pin Code Mode 48
Set Pin Code Barcode 48
Set Cradle Interface Barcode 49
7.5 DECODING SELECTION 56
Symbologies Selection 56
Disable All Symbologies 65
7.7 AZTEC SETTINGS 67
Structure Append Mode 67
Aztec Runes 67
GS1-128 Emulation 67
7.8 BPO SETTINGS 69
7.9 CANADA POST SETTINGS 70
7.10 CODABAR SETTINGS 71
Start/Stop 71
CLSI Library System 72
Concatenation 73
7.11 CODABLOCK SETTINGS 74
7.12 CODE 11 SETTINGS 75
Check Digits 75
7.13 CODE 39 SETTINGS 76
Accepted Characters 77
Reading Range 78
Reading Tolerance 78
GS1-128 Identifier 80
ISBT 128 82
GTIN Processing For GS1-128 83
Unconventional GS1-128 83
7.16 DATAMATRIX SETTINGS 84
7.17 DUTCH POST SETTINGS 85
Reading Type 86
Supplemental Setup 88
7.19 GS1 COMPOSITE SETTINGS 91
7.20 GS1 DATABAR SETTINGS 93
7.21 INFOMAIL SETTINGS 94
7.23 JAPAN POST SETTINGS 97
7.24 MATRIX 2 OF 5 SETTINGS 98
7.25 MAXICODE SETTINGS 99
7.26 MICROPDF417 SETTINGS 100
Symbology Identifier 100
Code 128 Emulation 100
Check Digit Verification 101
7.28 PDF417 SETTINGS 102
Irregular PDF 102
Control Header 102
Optional Fields 103
7.29 PLANET SETTINGS 105
Check Digit Transmission 105
7.31 POSTNET SETTINGS 107
7.32 QR CODE SETTINGS 108
Model 1 Control 108
7.34 SWEDEN POST SETTINGS 111
7.35 TELEPEN SETTINGS 112
7.36 TLC 39 SETTINGS 113
Linear Transmission Only 113
ECI security 113
Preamble 115
Postamble 116
Scantech-ID 117
8.1 SCANNING TRIGGERING 118
8.2 TIME OUT 121
8.3 GOOD READ MODE 122
8.4 BUZZER BEEP TONE 123
Beep Tone Setup 123
Good Read Beeps 123
Beep Duration 124
8.5 GOOD READ DURATION 125
Good Read Led Duration 125
Error Beep 125
Setup Beep 126
Chapter 9 Imager settings 127
9.1 IMAGER MODE 128
Appendixes 129
A.DECIMAL VALUE TABLE 130
B.ASCII TABLE 131
C.READABLE SYMBOLOGIES 132
1D Symbologies 132
2D Symbologies 132
D.TECHNICAL SPECIFICATIONS 133
E.SCAN MAP 135
F.OVERVIEW MODEL NUMBERS 137

Comentarios a estos manuales

Sin comentarios

Scantech Vega V-1010 Manual de usuario Pagina 12

Comentarios a estos manuales

Relacionado con productos y manuales para Lectores De Códigos De Barras Scantech Vega V-1010