Scantech Vega V-1010 Manual de usuario Pagina 10
- Pagina / 121
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
6 Installation of the VEGA V-1010
1.1 SAFETY & CAUTION
1. Please read the following safety statement carefully.
2. Please preserve this user manual for reference sometime.
3. Before cleaning the VEGA, the users must cut off all AC power. Do not
use liquid or spray type of detersive to clean the VEGA. Please use
dampish cotton cloth to clean the VEGA.
4. The outlet must set nearby the VEGA for connecting power easily.
5. Keep the VEGA dry to avoid short circuit.
6. During installation you must fix the equipment at solid table to avoid
damage caused by falling.
7. Before inserting power please ensure the voltage is healthy to the
equipment.
8. For safety please tie wire well and don’t put anything on the wire.
9. If you don’t use this equipment for long time, please cut off the power to
avoid damage from surge power.
10. Don’t spray any liquid on this scanner because it may cause a fire or
short circuit.
11. Please do not open the equipment. For safety only the qualified
serviceman can open the equipment.
12. If there are the following situations please contact with the qualified
serviceman to check this equipment.
(a) The damage of wire or pin of power supply.
(b) Some Liquid infiltrate into the equipment.
(c) The equipment has been exposed to wet environment.
(d) The equipment can’t work well.
(e) The equipment has any obvious damage, making the VEGA
working abnormally.
13. Don’t storage the VEGA at the temperature lower than -20°C (-4°F) or
higher than +70°C (158°F) to avoid any damage.
1.2 FCC WARNING
This equipment complies with the requirements in Part 15 of FCC.
- Handheld Bar code Scanner 1
- Scantech-ID VEGA 3
- Table of contents 5
- Introduction 8
- Chapter 1 Product Safety 9
- 1.1 SAFETY & CAUTION 10
- 1.2 FCC WARNING 10
- 1.3 SCANNER LABELLING 11
- 2.1 USE OF THE VEGA 14
- 3.1 V-1010 UNPACKING 16
- 3.2 V-1010 MOUNTING 17
- 4.1 V-1010BT UNPACKING 19
- 16 Configuring the VEGA 20
- Pairing 21
- 18 Configuring the VEGA 22
- Sleep Mode 23
- Memory Mode 23
- Chapter 5 Cover Display 24
- 5.1 SETUP COVER DISPLAY 25
- Message Format 25
- Change Cover Display 25
- 22 Configuring the VEGA 26
- 24 Configuring the VEGA 28
- 6.1 PREFACE 30
- 6.2 FACTORY DEFAULT SETTING 32
- Chapter 7 Programming Codes 33
- 7.1 GENERAL PROCESS 34
- Abort Configuration 34
- Set All Default 35
- Version Information 35
- 7.2 INTERFACE SELECTION 36
- Interface 36
- Scanner Pincode Mode 38
- Scanner Pincode Setup 39
- 7.4 BLUETOOTH CRADLE SETUP 40
- Cradle Pincode Mode 40
- Cradle Pincode Setup 40
- 7.5 SCANNER OPERATION 41
- Reading Mode 41
- Good Read LED Control 41
- Beeper Option 42
- Reading Level 42
- Accurany / Redundant Scan 42
- Reverse Output Characters 43
- 7.6 RS232 MODE PARAMETERS 44
- Baud Rate 44
- Data/Stop Bits 45
- Handshaking 46
- Terminal Type 47
- Country/Language 48
- Upper/Lower Case 49
- Interscan Code Delay 50
- 7.8 OUTPUT CHARACTERS 51
- Select Terminator 51
- 7.9 CODE TYPE 52
- Barcode Selections 52
- 50 Miscellaneous Parameters 54
- 7.10 UPC/EAN/JAN PARAMETERS 56
- Reading Type 56
- Supplemental Setup 57
- Check Digit Transmission 58
- 7.11 CODE 39 PARAMETERS 59
- Type of Code 59
- Output Start/Stop Character 59
- Decode Asterisk 60
- Set Up Code Length 60
- 7.12 CODE 128 PARAMETERS 62
- Append FNC2 62
- 60 Miscellaneous Parameters 64
- Set Up Number of Character 65
- Brazilian Banking Code 65
- 66 Miscellaneous Parameters 70
- 68 Miscellaneous Parameters 72
- 7.17 CODE 93 PARAMETERS 76
- 7.18 CODE 11 PARAMETERS 78
- 76 Miscellaneous Parameters 80
- 7.20 TELEPEN PARAMETERS 82
- Check Digit Transmission 84
- Application ID 84
- Symbology ID 84
- Symbology ID 86
- Default Barcode ID 88
- 8.1 BAR CODE ID 88
- User Define Code ID 89
- 86 Miscellaneous Parameters 90
- Setup Insertion 91
- Insertion Set Number 92
- Symbologies Selection 93
- 90 Miscellaneous Parameters 94
- Characters to be Inserted 95
- 8.3 CHARACTER DELETION 96
- Deletion Set Number 97
- Code Type to be Delete 98
- 96 Miscellaneous Parameters 100
- Appendixes 101
- B ASCII TABLE 103
- Less than 105
- Greater than 105
- Underscore 107
- C FUNCTION KEY TABLE 109
- E TECHNICAL SPECIFICATIONS 111
- (V-1010 wired model) 112
- (V-1010BT wireless model) 112
- F SCAN MAP 114
- G LED INDICATOR STATUS 116
- 1234 5670 117
- 1 234567 890128 117
- 12345 67890 118
- 123456 118
- I OVERVIEW MODEL NUMBERS 119
- Quick Configuration 120
Relacionado con productos y manuales para Lectores De Códigos De Barras Scantech Vega V-1010
(41 paginas)
(1 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales