Scantech Vega V-1010 Manual de usuario Pagina 12
- Pagina / 108
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
8 Installation of the VEGA V-1010
1.1 SAFETY & CAUTION
1. Please read the following safety statement carefully.
2. Please preserve this user manual for reference
sometime.
3. Before cleaning the VEGA, the users must cut off all
AC power. Do not use liquid or spray type of
detersive to clean the VEGA. Please use dampish
cotton cloth to clean the VEGA.
4. The outlet must set nearby the VEGA for connecting
power easily.
5. Keep the VEGA dry to avoid short circuit.
6. During installation you must fix the equipment at
solid table to avoid damage caused by falling.
7. Before inserting power please ensure the voltage is
healthy to the equipment.
8. For safety please tie wire well and don’t put
anything on the wire.
9. If you don’t use this equipment for long time, please
cut off the power to avoid damage from surge power.
10. Don’t spray any liquid on this scanner because it may
cause a fire or short circuit.
11. Please do not open the equipment. For safety only the
qualified serviceman can open the equipment.
12. If there are the following situations please contact
with the qualified serviceman to check this equipment.
(a) The damage of wire or pin of power supply.
(b) Some Liquid infiltrate into the equipment.
(c) The equipment has been exposed to wet
environment.
(d) The equipment can’t work well.
(e) The equipment has any obvious damage, making the
VEGA working abnormally.
13. Don’t storage the VEGA at the temperature lower than
-20°C (-4°F) or higher than +70°C (158°F) to avoid
any damage.
- VEGA V-1010 Linear Imager 1
- Scantech-ID VEGA 3
- Table of contents 5
- Introduction 10
- Chapter 1 Product Safety 11
- 1.1 SAFETY & CAUTION 12
- 1.2 FCC WARNING 13
- 2.1 USE OF THE VEGA 15
- 16
- 3.1 V-1010 UNPACKING 17
- Chapter 4 Cover Display 18
- Change Cover Display 20
- 18 Configuring the VEGA 22
- 5.1 PREFACE 24
- Programming Codes 24
- 5.2 FACTORY DEFAULT SETTING 26
- Chapter 6 Programming Codes 27
- 6.1 GENERAL PROCESS 28
- Abort Configuration 28
- Set All Default 29
- Version Information 29
- 6.2 INTERFACE SELECTION 30
- Interface 30
- 6.3 SCANNER OPERATION 30
- Reading Mode 30
- Good Read LED Control 31
- Beeper Option 31
- Reading Level 32
- Accurany / Redundant Scan 32
- Reverse Output Characters 33
- 6.4 RS232 MODE PARAMETERS 33
- Baud Rate 33
- Data/Stop Bits 34
- Handshaking 35
- Terminal Type 36
- Country/Language 37
- Upper/Lower Case 38
- Capslock Detection 38
- Character by ALT Method 39
- Select Numerical Pad 39
- Interscan Code Delay 40
- 6.6 OUTPUT CHARACTERS 41
- Select Terminator 41
- 6.7 CODE TYPE 42
- Barcode Selections 42
- 40 Miscellaneous Parameters 44
- 6.8 UPC/EAN/JAN PARAMETERS 46
- Reading Type 46
- Supplemental Setup 47
- Check Digit Transmission 48
- 6.9 CODE 39 PARAMETERS 49
- Type of Code 49
- Output Start/Stop Character 49
- Decode Asterisk 50
- Set Up Code Length 50
- 6.10 CODE 128 PARAMETERS 52
- Append FNC2 52
- 50 Miscellaneous Parameters 54
- Set Up Number of Character 55
- Brazilian Banking Code 55
- 56 Miscellaneous Parameters 60
- 58 Miscellaneous Parameters 62
- Transmission 63
- 6.15 CODE 93 PARAMETERS 66
- 6.16 CODE 11 PARAMETERS 68
- 66 Miscellaneous Parameters 70
- 6.18 TELEPEN PARAMETERS 72
- Check Digit Transmission 74
- Application ID 74
- Symbology ID 74
- Symbology ID 76
- 7.1 BAR CODE ID 78
- Default Barcode ID 78
- User Define Code ID 79
- 76 Miscellaneous Parameters 80
- Setup Insertion 81
- Insertion Set Number 82
- Symbologies Selection 83
- 80 Miscellaneous Parameters 84
- Characters to be Inserted 85
- 7.3 CHARACTER DELETION 86
- Deletion Set Number 87
- Code Type to be Delete 88
- 86 Miscellaneous Parameters 90
- Appendixes 91
- B. ASCII TABLE 93
- Less than 95
- Greater than 95
- Underscore 97
- C. FUNCTION KEY TABLE 99
- E. TECHNICAL SPECIFICATIONS 101
- F. SCAN MAP 102
- 1234 5670 104
- 1 234567 890128 104
- 12345 67890 105
- 1 23456 105
- H. OVERVIEW MODEL NUMBERS 106
- Quick Configuration 107
Relacionado con productos y manuales para Lectores De Códigos De Barras Scantech Vega V-1010
(121 paginas)
(41 paginas)
(1 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.133 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales